Freeze drying is to remove free water and part of bound water adsorbed in the gap of solid lattice under low temperature vacuum environment. Therefore, the freeze drying process is generally divided into five steps, namely pre-freezing, sublimation drying (or first stage drying), analytical drying (or second stage drying), endpoint judgment and product removal.
Food freeze drying equipment manufacturer: pre-freezing of products
This stage mainly plays a fixed role in order to dry the product. This is an extremely critical step, because if it is not handled properly, it will cause many product molding problems or quality problems. Therefore, it is necessary to strictly control the pre-freezing time, temperature and vacuum degree, but in actual production, the influencing factors of vacuum degree are often ignored in the pre-freezing process. The pre-freezing temperature is generally within 5°C below the freezing point, also known as the eutectic point temperature, or 10~15°C below the eutectic point temperature. The temperature jump point in this process is the appropriate pre-freezing temperature. When the temperature reaches the freeze-drying temperature, keep it for a period of time. The pre-freezing time is not fixed, and it can be completely frozen in 2-3 hours, which depends on the product load, plate area and the properties of the heat transfer medium.

Food freeze drying equipment manufacturers: sublimation drying of products
It is the main process of freeze drying, mainly to sublimate the ice in the material, but to ensure that the ice does not dissolve, the saturated vapor pressure at the freezing point of the material is higher than the steam around the ice. Therefore, it is necessary to quickly remove the generated water vapor and continuously replenish the heat required for sublimation. Temperature and pressure become the main influencing factors of this process. The first is the temperature during sublimation drying, which should be set below the eutectic point. The sublimation speed is fastest near the eutectic point. During the sublimation process, the interface between the dry layer and the frozen layer in the solid product will gradually decrease over time. When the interface between the dry layer and the frozen layer disappears (the frozen layer disappears), the temperature rise of the product at this time is significantly faster than before the frozen layer disappears. According to the production process of the product, it should be extended for several hours to ensure that all the frozen layers inside the product disappear.
Food freeze drying equipment manufacturers: analytical drying of products
After sublimation drying, all the ice crystals in the material will leave a lot of holes, but there will still be about 10% of unfrozen water left. By analytical drying, we mean to reduce this part of water and keep it at about 2%, which works in drying materials. The higher temperature of this stage should be determined according to the product properties and the required moisture content of the finished product, but the temperature can be appropriately increased to reduce the moisture content. In the re-drying stage, the aeration pressure needs to be appropriately increased to conduct heat. In order to speed up the drying speed and shorten the time, high vacuum can be restored when the product temperature completely reaches the temperature set by the heat transfer medium.
Food freeze-drying equipment manufacturer: freeze-drying end point judgment
In actual operation, the end time of analytical drying can be judged based on the following phenomena:
(1) The temperature of the product is basically consistent with the temperature of the heating rack and is maintained for a period of time.
(2) The pressure in the drying oven and the pressure in the cold trap tend to be consistent and are maintained for a period of time.
(3) Oven pressure. The cold trap temperature basically returns to the index when the equipment is unloaded and is maintained for a period of time.
(4) When the valve between the drying oven and the condenser is closed, the vacuum degree of the drying oven rises by less than 5Pa (0.05 bar) within two minutes to judge that the freeze-drying is over.
Food freeze-drying equipment manufacturer: freeze-drying curve design parameters
The freeze-drying curve can be divided into broad and narrow sense. The narrow freeze-drying curve refers to the curve of the relationship between the freeze-drying oven temperature and time. In a broad sense, the freeze-drying curve refers to the relationship curve between product temperature, plate (shelf) temperature, condenser (cold trap) temperature, vacuum degree and time during the freeze-drying process, as shown in the figure below. Usually, temperature and pressure are the ordinates, and time is the abscissa. Only by comprehensively controlling the parameters of each stage of the freeze-drying process can high-quality products be obtained. The freeze-drying curve is not only the basis for manual operation of the freeze dryer, but also the basis for automatic control of the freeze dryer operation.





