Low Energy Consumption Freeze Dryer
video

Low Energy Consumption Freeze Dryer

Name:freeze dryer
Size: from 0.5 to 200m²
Highlight: can be customized
Warranty:one year
Send Inquiry
Product Introduction

 

Low energy consumption Freeze Dryer

The quality and performance of different lyophilizers vary greatly. The performance related to the drying rate is mainly the cold trap temperature. The size of the pressure difference between the drying oven and the cold trap is determined by the temperature difference between the materials in the drying oven and the condenser. The greater the temperature difference between the two, the greater the pressure difference, the faster the stream flows from the drying oven to the condenser, and the shorter the drying time, Therefore, the cold trap temperature is an important factor affecting the operation cost. However, obtaining a lower cold trap temperature at the cost of higher energy consumption will still increase the operation cost, so the energy consumption index is also very important. In addition, the vacuum degree change and heat conduction capacity of the lyophilizer also have a certain impact on the operation cost.

So, how to get a low energy consumption freeze dryer? Here are some measures:

1. Control the pre-freezing speed to create an ice crystal structure conducive to sublimation. The pre-freezing speed is too fast, the ice crystal is small, the pores of the dried layer are fine, and the resistance of water molecules flowing through the dried layer is large, which affects the drying speed. Properly reduce the pre-freezing speed to make the ice grains coarse and the pores of the dried layer large, which will be conducive to the flow of water vapor and improve the drying speed, but the premise is to ensure the product quality.

2. Control the pre-freezing temperature. The pre-freezing temperature should be controlled below the eutectic point of the product. Too low will waste the cooling time for exceeding the temperature and the heating time for returning.

freeze dryer

3. Control the heating temperature. The initial heating temperature shall not be too high. The outer ice surface of the product is easy to be heated and melted. The heating temperature shall be carried out slowly from low to high. After the initial heating stage, the heating temperature can be increased as soon as possible when the cold trap capacity is allowed and the product temperature does not exceed the co melting point, so as to shorten the operation time under the condition of insufficient heating. The allowable heating temperature of different products is different. The higher the allowable temperature, the higher the heating temperature and the faster the drying speed.

4. Control of residual moisture content of the product. The residual moisture content of the product shall be appropriate. Too low will prolong the drying time, and too high is not conducive to the long-term storage of the product.

5. In the middle and later stages of drying, with the increase of the thickness of the dried layer of the product, like adding a layer of the insulation layer, it is more difficult to heat the ice surface, and the drying speed is greatly slowed down. In the vacuum environment, the air is thin, conduction and radiation are the main methods to heat the product ice, and improving the heat transfer is an effective method to speed up the drying speed.

6. Reduce the condenser temperature. Since a large number of water molecules from the drying oven are "captured" by the condenser, an ice layer is formed on the condenser surface, like covering the condenser surface with a cotton quilt. A temperature difference is formed between the condenser surface and the ice surface. The thicker the ice (generally 10 ~ 50mm), the greater the temperature difference (10 ~ 30 ℃). In this way, with the increase of frost thickness, the surface temperature of the frost layer gradually increases, even close to the surface temperature of the product ice layer, and the pressure gradually increases, resulting in the gradual reduction of the water vapor pressure difference between the freeze-drying box and the condenser, the gradual reduction of the drying rate, and even the cessation of frost capture, and the product will melt. Therefore, reducing the temperature of the condenser as much as possible will help to ensure the effective temperature difference and the pressure difference between the drying oven and the condenser. Generally, the temperature of the condenser is - 40 ℃ ~ - 50 ℃. Reducing the temperature of the condenser, such as - 60 ℃ ~ - 70 ℃ or even lower, will be limited by the cost. However, for products with low eutectic points, such as products below - 30 ℃, the freeze dryer equipment with a condenser temperature of - 60 ℃ ~ - 70 ℃ or even lower should be selected.

Kassel Machinery provides professional low energy consumption freeze dryer, welcome to inquire.

Parameter:

Model

KFD-1

KFD-2

KFD-5

KFD-6

KFD-8

KFD-10

Capacity (Kg/Batch)

10

20

50

60

80

100

Shelf Area (㎡)

1.1

2

5

6

8

10

Shelf Size (Mm)

500*400

700*500

800*895

950*800

1000*800

1190*800

Shelf Quantity (Layer)

5+1

6+1

7+1

8+1

10+1

11+1

Shelf Temperature (℃)

-60 to +70 

Water Catcher Temper (℃)

-65±5 

Max Catch Water(Kg)

15

30

75

90

120

150

Ultimate Vacuum

1

1

1

2

2

2

Electricity(Kw)

12

16

22

34

34

41

Size(Mm)

2200*1000*2000

2500*1000*2300

2200*1200*2400

3500*1400*2430

3500*1400*2430

4540*1400*2450

Weight(Kg)

1500

2000

2500

3000

3500

3800






Pre-sale:

* As soon as we get your inquiry, we will always reply to your email on time and try our best to recommend you the most suitable freeze dryer. Detailed tech info will also be provided for you.

* We can do sample tests for customers.

After-sale:

* If possible, please do come to our factory and we will teach workers the whole process of freeze-drying. The most appropriate time needed for freeze-drying will be tested by us.

* We will keep in touch with you, to make sure every part of the freeze dryer works well. One-year warranty, free online service for abroad customers.

Workshop:

Exhibition:

Hot Tags: Low Energy Consumption Freeze Dryer, China, factory, suppliers, manufacturers, customized, price, made in China, freeze dryer for sale, china freeze dryer, diagram of freeze dryer, china freeze dryer factory, freeze dryer for taxidermy, freeze dryer factory

Send Inquiry

whatsapp

skype

E-mail

Inquiry